What size string does a Craftsman weed eater use?

What size string does a Craftsman weed eater use?

craftsman trimmer line,weed eater string 0.065,0.065 trimmer line.

How do you put new line on a Craftsman weed eater?

Fold a length of line that is about 18 inches long in half. Insert one end through one of the holes in the hub and the other end through the other hole. Pull the line to extend it all the way out. It should align itself within the positioning tunnels on the head.

How do you wind a Craftsman line trimmer?

Start in the center of the spool and wind the line around the spool in the direction indicated by the arrows on the spool. Make sure that you wind the line neatly, with the turns aligned side-by-side and tight. When the line reaches the outer edge of the spool, cut it, leaving approximately 1 ft. of line unwound.

How do you restring a weed eater?

Place the spool back in the hub inside the trimmer head. Release the loose length of string from the notches in the spool. Feed the loose ends through the eyelets — usually called a line exit hole — in the trimmer head. Repeat with the second string, if applicable.

What size string does a Craftsman 25cc Weed Eater use?

This design gives you the choice of 2 different line sizes allowing you to get most any trimming job done! The Weedwacker® trimmer head feeds . 095″ bump and . 110″ fixed line.

How many feet of string does a Weed Eater need?

Most models recommend a specific length that varies between 16 and 26 feet. Weed Eater sells preloaded spools of trimmer string for models that accept them.

Does Weed Eater string size matter?

String Trimmer Line Thickness This probably comes as no surprise to anyone, but the general rule with string trimmer line is that the tougher the application, the thicker the line needs to be. A larger diameter will increase the power and durability of the line, which leads to less breakage and wear-out.

What is Craftsman easy start technology?

Start Easy The Craftsman Power Bit Start takes the hassle out of starting your line trimmer. There’s no more pulling of recoil start rope, just use the attachment on your power drill to get started fast. A safety lock mechanism prevents the unit from snapping back.

How do you wind a string trimmer head?

Nylon Line Installation:

  1. Cut one piece of line to recommended length; 0.95-.
  2. Align arrows on top of knob with openings in eyelets.
  3. Insert one end of trimmer lines into an eyelet and push line equal distance through trimmer head.
  4. Hold trimmer head while turning knob clockwise to wind line onto spool until about 5 in.

How do you replace string on Weed Eater?

Start by the preparation of the line.

  • Take out the retaining cap from the head of the weed eater.
  • After removing the cap,look for the starter hole,which is usually located in the center.
  • Wind the replacement string to the spool while following the arrow or direction marked in the spool.
  • How to replace string on a Homelite Weed Eater?

    Ensure that the trimmer is shut off and disconnected from all power. If the model is a gas-powered weed eater,remove the spark plug to avoid accidental startup.

  • Push in the tabs on the side of the spool retainer,and pull the spool upward to remove it from the trimmer head.
  • Remove any old string still on the spool.
  • How to restring a craftsman weedwacker?

    Firstly place the auto-feed trimmer on a flat surface.

  • Ensure the electric supply is shut and the trimmer clean from debris and dirt.
  • Push the tabs present on the immediate trimmer head sides to remove the spool cap.
  • Remove the old spool too.
  • You can now replace that old spool with using a line spool.
  • How do you replace a Weed Eater trimmer line?

    Determine the location and size of the Trackwall panels you want to install.

  • Use the stud finder to locate the wall studs,and mark their locations with pencil marks on the wall.
  • Hold the first Trackwall in position,and use a level to ensure it is level.
  • Attach the Trackwall to the wall and studs using number 10 flathead wood screws.